| Subject | Text |
| Poor connection somewhere. Check solder joints, reseat any plug-in cableing, etc. |
| sony tvs suffer from dry joints and they usually hide inside the metal canned units .but from what y |
|
|
| TRY LINE DRIVE | HI I HOPE THIS ADVISE HELP YOU TO FIX YOUR PROBLEM MITSUBISHI R COMMON FOR DRY SOLDER ON LINE DRIVE |
| str-de945 problem | Is the action (or lack thereof) intermittant? If so, it is likely a bad solder joint. The IR sensors |
| Uniden EXP970 continuously ringing | Hi
I have 3 years old never used Uniden EXP970 cordless phone.
If I connect it to the charger, |
| audi chorus always back in safe mode | hello, i just installed my original chorus, connected alle the wires as original and every time i tu |
| It sounds like a crook solder joint in the verticle section of the circuit board. Not too hard to fi |
| I don't have one in the shop right now but I think it might be a ground connection :?: I'm sure it |
| sony kv-28fd1e | he flashed 4 times,i solder the ic1509 again and he works 3 day,s
now he flashed again 4 times..
w |
| "
PostPosted: Tue Nov 13, 2007 11:45 pm Post subject: Yamaha RX-V-850 receiver
Any sugge |
| orion d9600a video recorder | hello
i have a D9600A VIDEO TWIN recorder i need to alter the out put channel as my tv station and |
| Playstation 2 | Hi. I have a play station 2, and i had a code for my doughter to watch DVD 's now forgot it ,is th |
| Absolutley Atom,
But I think knowing How much A User knows about electronics would allow the engin |
| Sanyo | You probably have a bad tuner or bad solder joints in the tuner area. Depending on what they find a |
| 1994 samsung CH-CKA50ZH model: CT--5315XVC screen blinking | my tv flashes/blinks after 5 seconds i turn on. i've noticed that if i lower the brightness setting |
| Re: Panasonic TV TX-25MD1 | [quote="Colin"]Panasonic TV. TX-25MD1
Hi there are two problems with this nine-year-old set.
A |
| Hi!
Today I´m happy beacuse I have found why the relay´s didn´t work properly. It |
|
|
| thanks | I got the manuals that you sent however I really am not that good at technical stuff. I was really |
| 1) Resolder all the output transistors solder joints and any other intermediate transistor stages th |
| Modle #. Could be a problem is the degausing. As always get any magnets away from the tv. (Speakers) |
| Re: Datasheet RS2004FS | [quote="sonyk70"]Hello, where i found the datasheet of RS2004FS?
Many thanks, sonyk.[/quote]
New |
| need user manual | hi frinds i have opel astra station with vcd cdr500 if any one have a user or service manual please |
| Yamaha RX-V-850 receiver | Any suggestions? My receiver will not engage with any FM stations. It just scans but never picks up |
| The main reason in gluing the bigger caps is to prevent movement while the PC board travels through |
| Often these errors are related to a bad solder joint on the main-pcb or crt-board.
You can check |
| Its easy to open that box.
You must unsolder the 5-6 foots of the box at the bottom of the board.
|
| Schematic / Manual. Sanyo Phone CLT - 6700. | Hi it would be very helpful if somebody would give me a copy of the schematic for Sanyo Cordless tel |
| [quote:0be7f001a9="Anonymous"][quote:0be7f001a9="jts1957"]What is "stucked mode?"
What i |
| Sony ST JX411 | I have a Sony am\fm tuner that has lost it's battery power to hold the station presets in memory.
|
| Sears 509-14370 TV, chassisA67 | Sears 509-14370 TV, chassisA67, made by JVC, the board is labeled CKF0822-DU3-1. TV turns on when f |